5/8"
Hand and Power Tools
View:
Active Filters :
- Main Category: Hand and Power Tools
- Alt. Size: 5/8" 8" 9/16"
Qty:
Qty:
Part #:511296
-
HIT-Z Anchor rod Anchor rod HIT-Z 5/8" x 9-1/2" #2018448Material, corrosionCarbon steel, zinc-platedWrench/nut size15/16 inDrill bit diameter3/4 inBase materialsConcrete (cracked), Concrete (uncracked)PROFIS SoftwareYesApprovals / Test reportsICC-ES report (concrete)Cleaning proceduresNon CleaningType of fixingPre-fastening, Through-fasteningProduct ClassUltimate
Part #:511896
-
5/8" Anchor Shackle, Screw Pin, Forged Carbon Steel, Painted Blue
Shackle Bodies Are Drop-Forged Carbon Steel
Self Colored (Painted Blue)
C-419-S Shackles Meet the Design Requirements of Federal Specification RR-C-271, Type IVA, Grade A, Class 2
Working Load Limit, Size, Manufacture Name, Date Code and USA Permanently Marked on Each Shackle
Statistically Tested for Impact Resistance, Tensile Strength, Hardness, Ductility and Fatigue
419 Series Shackles Meet or Exceed All Manufacturing Requirements of the ASME B30.26 &rdquoRigging Hardware&rdquo. These Include the Material Ductility Requirement (Section 26-1.1.2), the Design Factor Requirement (Section 26.1.2), the Identification Requirement (Section 26-1.5.1), and the Effective Temperature Range (Section 26-1.6.1). the Shackles Can Be Proof Tested in Accordance with Section 26-1.4
Certification Available Upon Request
6 to 1 Design Factor
Pins and Bolts Are Heat-Treated and Made of Alloy Steel
Qty:
Part #:500550
- 3/4" Drive Extensions
&bull Chrome plating provides increased protection from rust and corrosion
&bull Ball and spring socket retention
Qty:
Qty:
Part #:810222
- 1/2" Drive SAE 5/8" Standard Length Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:503703
- 5/8" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Qty:
Part #:504841
- Hex End L-Wrenches - ProGuard&trade Finish
Chamfered tool tips eliminate burrs and help tools seat in screw head
Sharp corners transfer more torque to the screw and reduce stripping
Precision machined for ease of use and superior fit
Qty:
Qty:
Qty:
Qty:
Qty:
Part #:811597
- 3/8" Drive 6-Point SAE 9/16" Deep Socket
SUPERTORQUE lobular openings for greater turning power without deforming the fastener
Designed for maximum engagement on 6-point fasteners
Qty:
Part #:501956
- 6 1/2" Cold Chisels
The most commonly used chisels in the chisel line
For cutting, shaping and removing metal softer than the cutting edge of the chisel
Qty:
Part #:811720
- 8" Combination Slip Joint Pliers Multiple parallel jaw positions are locked in to proper groove for superior non-slip performance
&bull Serrated jaws for maximum gripping power
&bull Polished heads resist rust and corrosion, extending the tool life
&bull Shear type wire cutter extends tool use
Qty:
Part #:501590
- 1/2" Drive SAE 5/8" Long Hex Bit Socket
&bull High-polished chrome finish socket cleans easily
&bull Two piece design allows bits to be replaced easily
Qty:
Part #:500375
- 9/16" 12-Point SAE SUPERCOMBO® Combination Wrench
&bull SUPERCOMBO® open end has specially designed grooves that direct wrench force away from fastener corners
&bull SUPERTORQUE® box opening design allows application of higher torque without rounding or deforming hex fastener points. No contact is made at the corners. Instead, wrenching forces are placed on the flat surfaces behind the points
&bull Meets or exceeds AErospace specification AS 954 for 12 point fasteners (as defined by AS 870) to provide accurate torque/tension relationship for precision application
&bull May be used on all common hex (6 point) fasteners with considerable advantage over conventional box end wrenches to increase both hand tool flexibility and economy
&bull Box and open end openings are identical
Qty:
Part #:503456
- 9/16" Shank Diameter Eyebolts Shoulder Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
Shoulder eye bolts must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:509570
- 5/8" Shank Diameter Eyebolts Plain Pattern
Forged from the best quality carbon steel, hardened and tempered to ensure increased strength and toughness and reduce liability or breakage
Each lot is tested and inspected to insure conformance to specifications
Available with UNC Class 2A thread only
Plain pattern eyebolts must never be used to lift an angular load
Eyebolt shanks should never be undercut or eyebolt shank diameters reduced
To obtain greatest strength from an eye bolt, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness and seating must be checked after initial load
Qty:
Part #:507665
-
5/8" Clevis Grab Hook, Forged Steel, Self Colored
Material is Drop-Forged Carbon Steel (Grade 30 & 43) or Heat-Treated Alloy Steel
Grade 30 & 43 Hooks Available Self-Colored or Zinc-Plated
Alloy Hooks Are Painted Orange and Stamped &rdquoAlloy&rdquo 3.5 to 1 Design Factor
Alloy Hook Sizes 1/4" to 3/8" are Supplied Individually Bagged and Unassembled
Self-Colored Finish Hooks Are Bulk Packed, Zinc Plated Hooks Are Packed 10 Per Box
Grab Hooks Are Designed to Grab a Chain Link and Hold it in Place
Hooks are Sized by the Material Diameter of the Chain That They Engage. Make Sure the Hook Size and Chain Diameter are Compatible Before Attaching to Load
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Part #:511957
-
5/8" x 6" Jaw & Eye Turnbuckle, Forged Carbon Steel, Galvanized
Drop-Forged Carbon Steel
Galvanized to Meet ASTM A-153 Specifications
5 to 1 Design Factor
See Figure C-780-G for Eye Dimensions
See Figure C-788-G for Jaw Dimensions
Jaws on Sizes 1/4&rdquo Through 5/8&rdquo Have Hex Head Bolt and Nut Jaws on Sizes 3/4&rdquo Through 1-1/2&rdquo Have Cotter Key and Bolt
IMPORTANT Instructions For Use
Turnbuckles are Designed for a Static Load
In Loads Where There is Vibration, Lock Nuts (Jam Nuts) Should be Used to Prevent the Connection from Turning or Loosening
DO NOT EXCEED THE WORKING LOAD LIMIT
Qty:
Qty:
Displaying: 1 - 24 of 81 Matching Items