1in
Underground Utility Supplies
View:
Active Filters :
- Main Category: Underground Utility Supplies
- End Connection: 1in
Part #:203957
- Straight Adaptors -22 CTS x MNPT ONE END MALE NATIONAL PIPE THREAD
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:203945
- Straight Couplings SAME CONNECTIONS ON BOTH ENDS - NO INTERNAL PIPE STOP ON STRAIGHT SIZES -22 CTS x -22 CTS
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:204386
- Straight Couplings SAME CONNECTIONS ON BOTH ENDS - NO INTERNAL PIPE STOP ON STRAIGHT SIZES -33 PEP-7 x -33 PEP-7
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:204022
- Plug Style - AWWA Inlets AWWA x -22 CTS
A.Y. McDonald Plug Style Corporation Stops come standard with a 360º operating head. The one piece body and plug are precisionmachined to assure a perfect match between the plug and the body to allow operating pressures of 100 PSI on 1/2&rdquo, 3/4&rdquo and 1&rdquo valvesand 80 PSI on 1 1/4&rdquo, 1 1/2&rdquo and 2&rdquo valves. This same machining precision carries over to the threads to assure A.Y. McDonald&rsquos highquality and compatibility with direct taps and saddle applications.
$
132.48
Qty:
Part #:206974
- Straight Ball Valves - Female National Pipe Thread (FNPT) x Female National Pipe Thread (FNPT)
90º ON/OFF TEE OPERATING HEAD FNPT x FNPT
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
214.16
Qty:
Part #:203886
- Straight Adaptors ONE END FEMALE NATIONAL PIPE THREAD -22 CTS x FNPT
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:204036
- SUBMITTAL INFORMATION • Manufactured in compliance with ANSI/AWWA C800 (latest revision)• Brass components in contact with potable water conform to ASTM B584, UNS C89833 (latestrevision) and identified with “NL”• Brass components not in contact with potable water conform to ASTM B62 and ASTM B584, UNSC83600 -85-5-5-5 (latest revision)• Large wrench flats provided for proper installation• ½” – 1” rated for 100 PSIG water pressure• 1 ¼” – 2” rated for 80 PSIG water pressure• Insert stiffeners required on all flexible plastic connections.:
$
237.00
Qty:
Part #:204390
- Straight Adaptors ONE END MALE NATIONAL PIPE THREAD -33 PEP-7 x MNPT
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:204704
- Tees SAME END CONNECTIONS ON ALL THREE SIDES -22 CTS x -22 CTS x -22 CTS
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:200120
- Straight Ball Valves Compression -33 PEP-7 x -33 PEP-7
90º DEGREE ON/OFF TEE OPERATING HEAD
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
343.29
Qty:
Part #:207113
- Straight 1&rdquo METER SWIVEL FITS 1&rdquo METERS, Meter Swivel x MIP L/wire seal hole 2.63in Length
Meter swivel nuts are less saddle, have internal straight threads per AWWA C700 and include hole for wire seal unless otherwiseindicated. EPDM rubber gaskets are supplied and are standard.(For Meter Dimensions see page 263)
$
37.56
Qty:
Part #:201741
- Tees SAME END CONNECTIONS ON ALL THREE SIDES -33 PEP-7 x -33 PEP-7 x -33 PEP-7
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:204034
- SUBMITTAL INFORMATION • Manufactured in compliance with ANSI/AWWA C800 (latest revision)• Brass components in contact with potable water conform to ASTM B584, UNS C89833 (latestrevision) and identified with “NL”• Brass components not in contact with potable water conform to ASTM B62 and ASTM B584, UNSC83600 -85-5-5-5 (latest revision)• Large wrench flats provided for proper installation• ½” – 1” rated for 100 PSIG water pressure• 1 ¼” – 2” rated for 80 PSIG water pressure:
$
233.00
Qty:
Part #:203927
- Straight Adaptors ONE END MALE NATIONAL PIPE THREAD Flare x MNPT
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:203902
- Straight Couplings SAME CONNECTIONS ON BOTH ENDS - NO INTERNAL PIPE STOP ON STRAIGHT SIZES Flare x Flare
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:203985
- Plug Style AWWA x Flare
A.Y. McDonald Plug Style Corporation Stops come standard with a 360º operating head. The one piece body and plug are precisionmachined to assure a perfect match between the plug and the body to allow operating pressures of 100 PSI on 1/2&rdquo, 3/4&rdquo and 1&rdquo valvesand 80 PSI on 1 1/4&rdquo, 1 1/2&rdquo and 2&rdquo valves. This same machining precision carries over to the threads to assure A.Y. McDonald&rsquos highquality and compatibility with direct taps and saddle applications.
$
124.48
Qty:
Part #:203475
- Straight Adaptors ONE END FEMALE COPPER FLARE -33 PEP-7 x Female Flare
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.The 74755 series fittings are designed to connect any A.Y. McDonald flare end to a different size or end connection.- Note 4755GSKT copper gasket included with all 74755 connections.
Qty:
Part #:200121
- Meter Couplings -Straight Meter Couplings - Straight 1-5/8" Length, FNPT x Male Meter Thread
Meter swivel nuts are less saddle, have internal straight threads per AWWA C700 and include hole for wire seal unless otherwiseindicated. EPDM rubber gaskets are supplied and are standard.(For Meter Dimensions see page 263)
$
35.86
Qty:
Part #:205634
- Angle Yoke Valves - Plug Style PLUG STYLE - 100 PSI - LOCKWING FOR 1&rdquo METERS
A.Y. McDonald angle yoke plug valves include a meter star nut for connection to iron yoke bars and a wide variety of inlet configurations.These angle valves come standard with 180º &ldquoopen to close&rdquo operating head and are directional with an arrow to indicate the direction of flow.- Insert stiffeners are required on all flexible plastic connections.
$
142.64
Qty:
Part #:130-5131-275
- Stop & Drain Straight Ball Valves - Flare orCompression x FNPT
90º ON/OFF TEE OPERATING HEAD - MINNEAPOLIS PATTERN BODY
A.Y. McDonald Stop & Drain Ball Curb Stops maintain a low turning torque and bubble-tight 150 PSIG water pressure rating due to thePTFE coated brass ball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and threadlocker. McDonald Stop & Drain Ball Curb Stops are available with a wide variety of end connections.All Stop & Drain Ball Valves are Directional and automatically drain from the outlet side when in the closed position
$
318.66
Qty:
Part #:130-5132-229
- 74753-33 1X3/4 ADAPTER PEP X MNPT-NL
Repair Part
No
Product Group
Service Fittings
Description
PEP-7xMNPT
Secondary Description
Straight MNPT Adapters
Inlet
PEP-7 (Size -33)
Insert Stiff Req
Yes
In Size
1
Material
NL Brass
Outlet
MNPT
Out Size
3/4
Part Type
Fittings
Series
74753-33
Prod Code
412
Product Line
Water Works
$
66.63
Qty:
Displaying: 1 - 21 of 21 Matching Items