Flare
Underground Utility Supplies
View:
Active Filters :
- Main Category: Underground Utility Supplies
- Connection: Flare IPS
Part #:204386
- Straight Couplings SAME CONNECTIONS ON BOTH ENDS - NO INTERNAL PIPE STOP ON STRAIGHT SIZES -33 PEP-7 x -33 PEP-7
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:204385
- Straight Couplings SAME CONNECTIONS ON BOTH ENDS - NO INTERNAL PIPE STOP ON STRAIGHT SIZES -33 PEP-7 x -33 PEP-7
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:201394
- Straight Adaptors ONE END MALE NATIONAL PIPE THREAD -33 PEP-7 x MNPT
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:203294
- Stainless Steel PEP Insert Stiffener ASTM D2239 SIDR 7 and 9, 2-3/8" Long
Qty:
Part #:200084
- Tees SAME END CONNECTIONS ON ALL THREE SIDES -33 PEP-7 x -33 PEP-7 x -33 PEP-7
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:200120
- Straight Ball Valves Compression -33 PEP-7 x -33 PEP-7
90º DEGREE ON/OFF TEE OPERATING HEAD
A.Y. McDonald Ball Curb Stops maintain a low turning torque and bubble-tight 300 PSIG water pressure rating due to the PTFE coated brassball that is supported by two blow-out proof EPDM seals. The end piece joint is sealed with an EPDM O-ring and thread locker. McDonaldBall Curb Stops offer positive shut-off from either direction and are available with a wide variety of end connections.
$
343.29
Qty:
Part #:201741
- Tees SAME END CONNECTIONS ON ALL THREE SIDES -33 PEP-7 x -33 PEP-7 x -33 PEP-7
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:204034
- SUBMITTAL INFORMATION • Manufactured in compliance with ANSI/AWWA C800 (latest revision)• Brass components in contact with potable water conform to ASTM B584, UNS C89833 (latestrevision) and identified with “NL”• Brass components not in contact with potable water conform to ASTM B62 and ASTM B584, UNSC83600 -85-5-5-5 (latest revision)• Large wrench flats provided for proper installation• ½” – 1” rated for 100 PSIG water pressure• 1 ¼” – 2” rated for 80 PSIG water pressure:
$
233.00
Qty:
Part #:203900
- Straight Couplings SAME CONNECTIONS ON BOTH ENDS - NO INTERNAL PIPE STOP ON STRAIGHT SIZES Flare x Flare
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:203902
- Straight Couplings SAME CONNECTIONS ON BOTH ENDS - NO INTERNAL PIPE STOP ON STRAIGHT SIZES Flare x Flare
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
Part #:204033
- SUBMITTAL INFORMATION • Manufactured in compliance with ANSI/AWWA C800 (latest revision)• Brass components in contact with potable water conform to ASTM B584, UNS C89833 (latestrevision) and identified with “NL”• Brass components not in contact with potable water conform to ASTM B62 and ASTM B584, UNSC83600 -85-5-5-5 (latest revision)• Large wrench flats provided for proper installation• ½” – 1” rated for 100 PSIG water pressure• 1 ¼” – 2” rated for 80 PSIG water pressure:
$
142.00
Qty:
Part #:130-4130-894
- Stainless Steel PEP Insert Stiffener ASTM D2239 SIDR 7 and 9, 2-3/8" Long
Qty:
Qty:
Part #:130-5120-117
- Elbows - 1/4 Bend. ONE END FEMALE COPPER FLARE Swivel Female Flare x Flare
A.Y. McDonald Service Fittings are manufactured to meet or exceed the AWWA C800 (latest revision) standard. Our service fittings arerated to withstand the same pressures as the tubing they are designed to fit. They are designed and tested for cold potable water only.EPDM rubber gaskets are used in our Compression fittings.
Qty:
$
503.11
Qty:
Displaying: 1 - 15 of 15 Matching Items